#43 Focusrite Scarlett 18i6 teardown

As it turns out, i hadn't done (or at least documented) a teardown of this little guy, even though i've been using it for the last two years or so. Even though, as it turns out, i bought this a few months after starting this blog. Either way, i just put it up for sale (due to upgrading to the Scarlett 18i20 i inspected the other week). So i figured i might as well snap a few photos before it goes to its next owner (whomever that may be).

#37 Presonus Audiobox 1818VSL teardown and troubleshooting (part 1)

Together with the pair of Konnekt x32's (one of which is dealt with in the previous write-up here), i also got one of these Presonus Audiobox 1818VSL's. Also sold as untested, but powered up and allegedly detected by a Mac, so i figured it couldn't have been too far gone (or fubar'd).

The reality of it turned out to be a wee bit more complicated than one might've hoped...

#31 Warwick ProFET 5.1 bass amplifier teardown & maintenance

A local buddy just brought this German beastie in, citing a dicky DI output, and an unhealthy-sounding fan. Well, when i say "German", i mean the brand itself; as one might expect, it's "obviously" made in China, as it says on the back. But isn't nearly everything (else), anyway?

#25 Behringer ADA8000 "Ultragain Digital" revival

I got my hands on one of these Behringer Ultragain Pro-8 Digital a few months ago, as faulty (as in, totally dead) for about 50$ shipped. Having done some preemptive googling before going for it, i was expecting the transformer to be toasted. Sure enough, that's exactly what the problem was - one half of the center-tapped primary measured in the hundreds of kohm, so pretty much open-circuit (as opposed to the 50-odd ohms the remaining good half measured).

Initially i was planning on finding / getting a "drop-in replacement" toroidal transformer, ie. similarly sized physically and power-wise, but with less insanely-high secondary voltages. The stock one, according to some "inspection notes" i found online, seems to have had roughly 2x20VAC windings for the analog +/-15V (meaning the voltage regulators had to "burn off" uselessly much power / voltage), 12VAC for the 5V regulators, and a whopping 58VAC winding for the phantom power regulator. That's about a 50% overkill across the board. One can only wonder just what possessed them to spec the transformer quite like that, especially since it must've been a custom order - you'll rarely find retail units with more than two (identical) secondary windings, and when you do, expect to pay a pretty penny for'em.

#21 SM Pro Audio TB202 dual tube preamp / channel strip modding & upgrade

<Further developments can be found in parts two, three and four>

I'll admit, this was a bit of a lucky catch, in that it was mistakenly listed in the wrong eBay category, but one i "stalk" for good deals on certain faulty bits of audio gear. It was up for auction, there didn't seem to be much demand for it, and i ended up winning it for a mere 21 euros. About as much as the shipping for it ended up costing, oddly enough.

But still, even for some 40-odd bucks, not a bad little unit. Two channels, a (bare-bones-ish) compressor on each (1.5-10:1 ratio, 1ms/5ms attack, 500ms/1500ms release, at least according to the specs in the manual), as well as 3-band EQ (80Hz shelving / 1.8kHz bell / 8kHz shelving), and there's a tube / valve involved in the circuitry as well. If nothing else, i figured it would do nicely as a bass DI (or even an overdriven preamp, once some internal re-wiring is figured out and done).

#20 SM Pro Audio TB202 power supply repair

<Some sort of continuation from another post>

Buuuuut that brings us to what might as well amount up to the proverbial "elephant in the room" - the power supply. No markings or label anywhere on it - if i didn't know any better, i could almost say it never had any (no adhesive residues or anything). Fortunately, it was held together with four Phillips-head self-tapping screws, so "disrobing" it wasn't unecessarily traumatic. That being said, what greeted my eyes, sort of WAS.

#13 Fisher RS-1022 rehabilitation and bling-ification

So i had this old Fisher RS-1022 Studio Standard stereo receiver brought in, with one of the fuses in-line with the speaker outputs blown. Fair enough, that was easy enough to replace, they made it quite easy, with the fuseholders being mounted right on the rear panel. The clamps were nowhere near as elastic (or firm) as they might've once been, but with a pair of needle-nose pliers and a bit of creativity, that was no biggie.

Second issue, five of the six lamps that illuminate the tuning scale and the radio signal level were dead. In four of the dead ones, the fillament was attached only at one end, and in the fifth, it was attached at neither end. Interesting little lamps, 6.3v AC, 250mA, in a similar casing as 6x32mm glass fuses. Good luck finding replacement ones (which may very well just end up dying again anyway); these will get replaced with a few white LEDs recovered from a laptop display's backlight.

#9 Revisited: Amphion Impact 500 (DB Series DB5004) subwoofer amplifier - DONE!

Got the fresh parts the other week, and installed them all. That, plus rebuilding the two blown and "distressed" traces, respectively.

#4 Dunlop Zakk Wylde ZW45 wah pedal teardown & repair

Ok, this one's a real quickie. One of the guitarists in my band got this wah (Dunlop ZW45 Zakk Wylde Cry Baby Wah) as a gift a number of years ago, and in the last few weeks it developed crackly and intermittent sound (regardless of being on or off).

Initial fiddling with the power / input / output jacks pointed towards a questionable patch-cable, but even that soon stopped working, which then turned my suspicions towards cracked solder joints (rather than the jack sockets themselves).