#34 MOTU Traveler mk3 teardown and repair

Hunting for faulty stuff on eBay has been fruitful yet again: this time, a MOTU Traveler mk3 Firewire audio interface. The reported issue was by now, the "classic", dead Firewire.

A pretty comprehensive little package, with loads of features shoehorned into quite a compact package - 1RU thickness / height, but only about 80% of the width.

#21 SM Pro Audio TB202 dual tube preamp / channel strip modding & upgrade

<Further developments can be found in parts two, three and four>

I'll admit, this was a bit of a lucky catch, in that it was mistakenly listed in the wrong eBay category, but one i "stalk" for good deals on certain faulty bits of audio gear. It was up for auction, there didn't seem to be much demand for it, and i ended up winning it for a mere 21 euros. About as much as the shipping for it ended up costing, oddly enough.

But still, even for some 40-odd bucks, not a bad little unit. Two channels, a (bare-bones-ish) compressor on each (1.5-10:1 ratio, 1ms/5ms attack, 500ms/1500ms release, at least according to the specs in the manual), as well as 3-band EQ (80Hz shelving / 1.8kHz bell / 8kHz shelving), and there's a tube / valve involved in the circuitry as well. If nothing else, i figured it would do nicely as a bass DI (or even an overdriven preamp, once some internal re-wiring is figured out and done).

#20 SM Pro Audio TB202 power supply repair

<Some sort of continuation from another post>

Buuuuut that brings us to what might as well amount up to the proverbial "elephant in the room" - the power supply. No markings or label anywhere on it - if i didn't know any better, i could almost say it never had any (no adhesive residues or anything). Fortunately, it was held together with four Phillips-head self-tapping screws, so "disrobing" it wasn't unecessarily traumatic. That being said, what greeted my eyes, sort of WAS.

#19 Takstar / Gear4Music WPM-200 Wireless Monitor System part 3: transmitter mods

And at long last(?), we've reached the point where we take a look at the transmitter end of this wireless monitoring system. Not a whole lot to see on the outside, really: power switch, power LED, channel select rotary switch (1 to 6) on the front, and the DC input barrel socket and the 1/4" stereo input jack socket on the back.

#13 Fisher RS-1022 rehabilitation and bling-ification

So i had this old Fisher RS-1022 Studio Standard stereo receiver brought in, with one of the fuses in-line with the speaker outputs blown. Fair enough, that was easy enough to replace, they made it quite easy, with the fuseholders being mounted right on the rear panel. The clamps were nowhere near as elastic (or firm) as they might've once been, but with a pair of needle-nose pliers and a bit of creativity, that was no biggie.

Second issue, five of the six lamps that illuminate the tuning scale and the radio signal level were dead. In four of the dead ones, the fillament was attached only at one end, and in the fifth, it was attached at neither end. Interesting little lamps, 6.3v AC, 250mA, in a similar casing as 6x32mm glass fuses. Good luck finding replacement ones (which may very well just end up dying again anyway); these will get replaced with a few white LEDs recovered from a laptop display's backlight.

#4 Dunlop Zakk Wylde ZW45 wah pedal teardown & repair

Ok, this one's a real quickie. One of the guitarists in my band got this wah (Dunlop ZW45 Zakk Wylde Cry Baby Wah) as a gift a number of years ago, and in the last few weeks it developed crackly and intermittent sound (regardless of being on or off).

Initial fiddling with the power / input / output jacks pointed towards a questionable patch-cable, but even that soon stopped working, which then turned my suspicions towards cracked solder joints (rather than the jack sockets themselves).

#3 MOTU 8Pre teardown & gain adjustment pot replacement

On the latest drum tracking session i surprisingly discovered that channel 8 on the MOTU 8pre in my recording rig was noisy and useful-signal-less. This same unit had a similar issue with channel 6 when i bought it (as faulty, with a shot Firewire chip).

Fortunately, when i was about to take care of ch6, i got two replacement pots. When investigating the issue, i had read it's a relatively common occurrence, so i figured that as long as i'm contacting the local MOTU distributor, might as well get an extra / spare one, just in case (especially since i had two 8Pres at the time).